I’ll research Sensirion’s SHT41-AD1B-R3 documentation and sourcing options, then save a cited application guide in the project files, clearly distinguishing verified facts from unknowns.
I verified the pinout, reference circuit, and electrical limits, including that the R3 ordering code specifies a 10,000-piece reel. I’m writing the guide with two cross-manufacturer alternatives labeled as redesign options, not drop-in replacements, and flagging the package pitch and distributor MOQ as unverified.
The Sensirion SHT41-AD1B-R3 is a digital relative-humidity and temperature sensor with an I²C interface and fixed 7-bit address 0x44. Its common use is ambient monitoring in battery-powered data loggers, HVAC controls, and IoT sensor nodes, where the board must expose the sensor to representative air rather than board-generated heat; see the Sensirion design guide.
1. Quick Specifications
Absolute maximum/stress ratings are not operating targets. Typical accuracy is not a g...
Created the SHT41-AD1B-R3 Application and Usage Guide in project files, covering all seven requested sections with manufacturer citations and source links. It includes practical I²C wiring, layout and heater precautions, sourcing guidance, and two clearly labeled non-drop-in alternatives.
Package pitch and distributor MOQ remain explicitly unverified; confirm those before footprint release or purchasing.
The Sensirion SHT41-AD1B-R3 is a digital relative-humidity and temperature sensor with an I²C interface and fixed 7-bit address 0x44. Its common use is ambient monitoring in battery-powered data loggers, HVAC controls, and IoT sensor nodes, where the board must expose the sensor to representative air rather than board-generated heat; see the Sensirion design guide.
1. Quick Specifications
Absolute maximum/stress ratings are not operating targets. Typical accuracy is not a guaranteed error limit over the entire temperature and humidity range.
Table
Parameter
Classification
Value and conditions
Supply voltage, VDD
Electrical operating range
1.08–3.6 V; 3.3 V typical.
SDA/SCL voltage stress limit
Absolute maximum
VSS −0.3 V to VDD +0.3 V. Do not use this as the logic operating range.
Separate absolute-maximum VDD rating
Unverified
A separate numeric supply-stress limit was not verified in this research; never assume that VDD +0.3 V permits raising the supply beyond its operating range.
Operating temperature
Rated operating range
−40 to +125 °C.
Normal recommended environment
Best-performance conditions
5–60 °C and 20–80 %RH.
Storage temperature
Absolute-maximum table
−40 to +150 °C; not a recommendation for long-term storage.
RH accuracy
Typical sensor specification
±1.8 %RH; consult the datasheet accuracy curves and footnotes for environmental dependence.
Temperature accuracy
Typical sensor specification
±0.2 °C; consult the temperature-dependent accuracy envelope.
Humidity response
Response, not conversion time
τ63% = 4 s.
Idle current, heater off
Typical / maximum
0.08 µA typical; 1.0 µA maximum at 25 °C, 3.4 µA maximum at 125 °C.
Measurement current, heater off
Typical / maximum
320 µA typical, 500 µA maximum.
Average sensor current at one measurement/s
Typical, heater off
2.2 / 1.2 / 0.4 µA for high / medium / low repeatability respectively; excludes external bus pull-up losses.
Highest heater setting
Typical / maximum current
Nominal “200 mW” setting: 60 mA typical, 100 mA maximum. Size the supply for this load if enabled.
Package
Mechanical
Four-pin DFN, nominal 1.5 × 1.5 × 0.5 mm, open sensing cavity on top.
Pad pitch
Unverified
Not reliably verified from the package drawing; inspect Figure 15 and the recommended land pattern before footprint release. Do not infer pitch from body size.
2. Pinout & Connections
Pin numbers below follow the manufacturer's assignment; check the package orientation drawing and pin-1 marking before assigning PCB pads.
Table
Pin Number
Pin Name
Description
Best Practice
1
SDA
Bidirectional serial data.
Connect to MCU SDA; use a pull-up to the sensor supply. The reference circuit uses 10 kΩ.
2
SCL
Serial clock input.
Connect to MCU SCL; use a pull-up to the sensor supply. The reference circuit uses 10 kΩ.
3
VDD
Supply voltage.
Connect to a regulated rail within 1.08–3.6 V; decouple to VSS with 100 nF.
4
VSS
Ground.
Tie to the MCU supply ground; keep the local bypass-capacitor return short.
The ordering entry specifies 0x44; there is no address-selection pin in the four-pin assignment. Use 0x44 with APIs that take a 7-bit address, rather than an address already shifted for the R/W bit.
3. Standard Application Circuit
SHT41 3.3 V I²C wiring
Use a shared regulated 3.3 V rail for the MCU's compatible I/O domain and sensor. Connect VDD (pin 3) to that rail, VSS (pin 4) to ground, SDA (pin 1) to MCU SDA, and SCL (pin 2) to MCU SCL; place a 100 nF ceramic capacitor directly between sensor VDD and VSS and fit one 10 kΩ pull-up per bus line to VDD, following the manufacturer's typical application circuit.
Engineering implementation guidance:
Treat the reference pull-up value as a starting point, not a universal value. Check the combined pull-ups already installed on the bus and verify rise time at the actual capacitance and bus speed. Do not blindly parallel another set.
Do not connect directly to a 5 V rail or pull SDA/SCL up to 5 V. The operating supply limit is 3.6 V and the signal stress limit tracks VDD; use a suitable bidirectional I²C level translator where needed.
If switching sensor power, prevent the host or bus pull-ups from holding SDA/SCL above the unpowered device's allowed pin voltage.
If the heater will be used, budget up to 100 mA for the highest setting and evaluate local bulk capacitance and regulator transient response; the mandatory reference 100 nF capacitor alone is not a guarantee against rail droop.
Minimal firmware transaction
Write command 0xFD for a high-repeatability measurement, wait at least the 8.3 ms maximum conversion time, then read six bytes. Commands 0xF6 and 0xE0 select medium and low repeatability with maximum conversion times of 4.5 ms and 1.6 ms respectively. The response is temperature MSB/LSB/CRC followed by humidity MSB/LSB/CRC; validate each word using CRC-8 polynomial 0x31, initialization 0xFF, no reflection, and final XOR 0x00 before accepting the sample. An early read can NACK while conversion is still running; this is distinct from a missing device.
Use the manufacturer embedded driver for conversion and protocol handling rather than assuming another sensor's register map applies. LED resistor calculations, USB CC resistors, and shield connections are not applicable to this sensor.
4. PCB Layout & Routing Guidelines
Decoupling: Place the reference 100 nF capacitor next to VDD/VSS, with a short supply/return loop rather than a long path through the board. The short-loop placement is engineering implementation guidance.
Thermal isolation: Place the sensor away from regulators, MCUs, displays, and power stages; remove unnecessary surrounding copper and consider slots or a small sensor island/flex PCB to reduce heat conduction. Sensirion's Design Guide, Version 2, March 2024 recommends thin metal connections and milled/etched slits. Source text was read directly; citation-backed extraction for this application note remains unresolved.
Air access: Put the sensing cavity near an enclosure vent with low dead volume; avoid airflow heated by other components. Follow the same Sensirion design guide. Do not trade electrical correctness for thermal isolation.
Routing and heater supply: SDA/SCL are single-ended I²C signals, not a differential pair; controlled differential impedance and pair-length matching are unnecessary. Keep them short and away from switching nodes. Size VDD/VSS traces and any thermally isolating neck for the 100 mA maximum heater load if enabled; check voltage drop rather than using an arbitrary high-current trace-width rule. No universal trace width or thermal-relief spoke dimension was verified.
Land pattern and assembly: Use the manufacturer's recommended land pattern and stencil, not a generic DFN footprint chosen by body dimensions alone. Keep the top opening free of coating and contaminants, and do not board-wash the sensor, as directed in Handling Instructions, Version 9, June 2025. Source text was read directly; citation-backed extraction for this application note remains unresolved.
5. Common Pitfalls / Things to Watch Out For
Treating it as a 5 V-compatible generic I²C sensor. Overvoltage, pull-ups to the wrong rail, or back-powering a switched-off sensor can violate its electrical limits. Keep VDD within 1.08–3.6 V and SDA/SCL within their allowed voltage window, and check all existing bus pull-ups.
Measuring board heat or contaminating the cavity, then calling the result ambient humidity. Thermally isolate the sensor and preserve access to representative air; do not wash or coat its opening. See the design guide and handling instructions. Heater-on measurements are not within normal sensor specifications: keep heater duty cycle below 10%, operate the heater only below 65 °C ambient, and allow the sensor to return to ambient conditions before treating a reading as environmental data.
6. Popular Alternatives & Equivalents
No verified cross-manufacturer drop-in replacement was established. These are functional alternatives for a controlled redesign, not substitutions into the existing symbol, footprint, or firmware.
Digital RH/temperature sensor; 1.62–5.50 V; 8-pin WSON, 2.50 × 2.50 mm; I²C with four address options.
Functionally similar only; not pin-compatible or footprint-compatible.
Replace symbol/footprint, review the additional pins and supply constraints, and port the command protocol. Flux library filtering returned inconsistent metadata, so no usable library entry was verified for this guide.
Environmental sensor with I²C; 8-contact metal-lid LGA, 2.5 × 2.5 × 0.93 mm; VDD 1.71–3.6 V and VDDIO 1.2–3.6 V.
Functionally similar only; not pin-compatible or footprint-compatible.
Redesign the footprint and supply wiring; implement Bosch register configuration and compensation. The found Flux library entry describes a breakout/module despite its 8-terminal metadata: inspect it before use and do not assume it represents the bare IC correctly.
The alternatives' full accuracy envelopes, availability, and lifetime status must be checked during qualification; this guide does not certify equivalent measurement performance or current stock.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Exact-MPN listings were returned for DigiKey, Mouser, and Arrow. For JLCPCB assembly, the catalog lists C3664396; a catalog listing is not proof of assembly stock.
Packaging Options
Manufacturer R3 ordering quantity: 10,000 pcs. Distributor cut-tape and custom-reel options must be confirmed on the quotation; the DigiKey page could not be directly read during this research.
Standard MOQ
10,000 pcs per manufacturer R3 order/reel quantity, not a universal distributor MOQ. A one-piece cut-tape MOQ was not verified from an accessible primary distributor page; do not assume it is available.
Sourcing Advice
Specify the complete SHT41-AD1B-R3 code and Sensirion orderable number 3.000.611. Confirm package, reel quantity, date code, traceability, lead time, and assembly availability. Prefer manufacturer-confirmed franchised channels; independently brokered or marketplace stock carries counterfeit and handling/contamination risk. Do not interchange suffixes without checking the ordering table.
Sourcing listings were checked on October 7, 2026. No purchase was placed; this document makes no guarantee of live stock, price, distributor authorization, or delivery date.
Sources
Sensirion, Datasheet – SHT4x, Version 7.3, June 2026, manufacturer PDF: typical application, sensor/electrical specifications, timings, pin assignment, package, and ordering information.
Sensirion, Design Guide for Humidity and Temperature Sensors, D1, Version 2, March 2024, manufacturer PDF. Direct source read supports the practical thermal/airflow guidance; structured citation extraction remained pending after retries.
Sensirion, Handling Instructions for SHTxx Humidity and Temperature Sensors, D1, Version 9, June 2025, manufacturer PDF. Direct source read supports board-wash/coating guidance; structured citation extraction remained pending.
Texas Instruments, HDC302x datasheet, Rev. D, manufacturer PDF, and HDC3020DEFR ordering page. TI's product documentation lists the Rev. D release as July 24, 2024.
Bosch Sensortec, BME280 Datasheet, cover identifies Revision 1.24, February 2024, manufacturer PDF. Some extracted internal footer text retains older revision identifiers; use the manufacturer-hosted document and verify the release during qualification.
Distributor/manufacturing catalog links in Section 7 are sourcing references, not substitutes for the manufacturer electrical specifications.
Unverified items retained explicitly: pad pitch; separate absolute-maximum supply-stress value; distributor cut-tape/custom-reel options and MOQ; current stock/lead time; bare-IC suitability of the linked BME280 library entry. This guide documents integration practice and does not constitute a validation of the current Flux symbol, footprint, or 3D model.