Crystal Application Guide


Thought for 6 mins 22 sec
Thought for 8 sec
Thought for 5 sec
Referenced guidance.
Thought for 8 sec
Created 2 tasks.
1/2 Research and write the cited crystal application guide

Research and write the cited crystal application guide

Verify guide coverage, specifications, and citation integrity

Accessed knowledge for the next task.
Thought for 19 sec
Awaiting 1 task
Thought for a moment
"Crystal Application Guide" completed.
The guide is drafted with cited specifications and RTC integration guidance. I’m tightening the alternatives section so it lists verified components and clearly distinguishes functional similarity from drop-in compatibility.
Thought for 11 mins 51 sec
Thought for 11 sec
Thought for 27 sec
Awaiting 1 task
"Crystal Application Guide" completed.
Saved the cited Application & Usage Guide in the project files, covering specifications, connections, load-capacitance selection, layout, pitfalls, alternatives, and sourcing.
Remaining limitations: Only one alternative has fully verified electrical specifications; the second candidate’s suffix details and both candidates’ drop-in footprint compatibility remain unverified and are explicitly flagged.

ECS-.327-6-34QCS-TR Application and Usage Guide
The ECS-.327-6-34QCS-TR is an AEC-Q200-qualified, 32.768 kHz tuning-fork crystal for RTC and low-power MCU clock circuits, specified for a 6 pF load and operation from -40°C to +125°C. It is a passive two-terminal resonator—not a powered oscillator—so reliable operation depends on the host Pierce amplifier, effective load capacitance, drive level, startup margin, and PCB parasitics; see the ECS product page and ECX-34Q datasheet.
1. Quick Specifications

Table


ParameterValueClassification / Notes
Nominal frequency32.768 kHz Operating / nominal
Frequency tolerance±10 ppm at +25°C Operating specification; initial tolerance, not total error across temperature and aging
Load capacitance, CL6 pF Operating / specified circuit load
ESR (R1)70 kΩ maximum Maximum; use for startup-margin analysis
Operating temperature-40°C to +125°C Operating range
Storage temperature-55°C to +125°C Manufacturer-specified non-operating range; the datasheet does not title it an absolute-maximum table
Drive level0.1 µW typical; 0.5 µW maximum Typical and maximum values in the electrical-characteristics table; not presented under a formally titled absolute-maximum section
Shunt capacitance, C01.1 pF typical; maximum not specified Typical; do not treat as a guaranteed maximum
First-year aging±3 ppm maximum at +25°C ±3°C Maximum
Package3.2 mm × 1.5 mm × 0.9 mm maximum 2-SMD, ECX-34Q / 3215 class
QualificationAEC-Q200 qualified Automotive passive-component qualification
Supply voltage / currentN/APassive crystal; voltage and supply-current ratings are not specified as for an active oscillator
2. Pinout & Connections

Table


Pin NumberPin NameDescriptionBest Practice
1XTAL1 / In-OutFirst interchangeable crystal electrode; datasheet connection is “In/Out.” Connect to the MCU/RTC oscillator input or output exactly as shown in the host IC reference circuit; keep the node short and isolated.
2XTAL2 / Out-InSecond interchangeable crystal electrode; datasheet connection is “Out/In.” Connect to the other oscillator terminal; place its load capacitor adjacent to the host pin/crystal loop.
The resonator is non-polarized: ECS labels pin 1 “In/Out” and pin 2 “Out/In,” indicating that the two crystal electrodes are functionally interchangeable. The package drawing’s detailed bottom-terminal and recommended-land dimensions were not machine-verified; use the official ECX-34Q drawing rather than reconstructing the footprint from this guide.
3. Standard Application Circuit
Use the part across the host MCU/RTC OSC_IN and OSC_OUT (or equivalent) pins. Connect load capacitor CL1 from OSC_IN to the oscillator ground and CL2 from OSC_OUT to the same quiet ground, unless the IC integrates one or both capacitors.
For a Pierce oscillator:
CL = (CL1 × CL2) / (CL1 + CL2) + Cs
Here, Cs includes MCU/RTC pin capacitance plus PCB parasitics. If CL1 = CL2 = C, the first-pass relationship is C ≈ 2 × (6 pF − Cs), but this is not a universal capacitor value: first check the host IC’s internal programmable/fixed capacitance and its oscillator application note. Do not add external capacitors blindly when the IC already provides the required effective load.
Validate the completed circuit over voltage, temperature, component tolerance, and production spread. Measure or calculate startup margin with the host-vendor method; ST recommends gain margin greater than 5 when transconductance data is used, while its LSE-specific safety-factor guidance identifies Sf ≥ 3 as safe and Sf ≥ 5 as very safe. Also verify drive level: DL = ESR × IQ²; exceeding the crystal’s 0.5 µW maximum can reduce life or damage the resonator. Add a series resistor only if measurement shows excessive drive, then recheck startup margin.
4. PCB Layout & Routing Guidelines
  • Place the crystal and any external load capacitors immediately beside the MCU/RTC oscillator pins; minimize loop area and trace length.
  • Keep clocks, switching nodes, PWM, RF, and other fast/high-amplitude signals away from both crystal nets.
  • Use a quiet local oscillator-ground region/guard tied to the nearest host-IC ground as recommended by the MCU/RTC vendor; avoid return-current paths from noisy loads through this region.
  • Avoid vias and test pads on the high-impedance crystal nodes where practical; their capacitance changes the effective CL and can reduce startup margin.
  • Follow the official ECX-34Q land pattern. The package body is verified as 3.2 mm × 1.5 mm with 0.9 mm maximum height, but the drawing-derived land dimensions remain explicitly unverified in this guide.
5. Common Pitfalls
  1. Choosing load capacitors by copying another design. The 6 pF rating is the total effective load seen by the crystal, including internal pin capacitance and PCB stray capacitance—not the value of each external capacitor. Excess load can pull frequency and weaken startup; insufficient load also shifts frequency.
  2. Checking oscillation only at room temperature. A circuit may start on the bench yet fail at voltage/temperature corners or after tolerance variation when margin is low; validate startup time, gain/safety factor, and drive level across worst-case conditions.

Table


Manufacturer / Exact MPNComparisonFlux LibraryCompatibility Status
Abracon ABS07AIG-32.768KHZ-6-1-TThe exact ordering code selects 6 pF (6), ±10 ppm (1), -40°C to +125°C (blank temperature option), and 3,000-piece tape/reel (T). The package is 3.2 ±0.15 mm × 1.5 ±0.15 mm × 0.9 mm maximum, but ESR is 80 kΩ maximum across the full -40°C to +125°C range—not 70 kΩ. Available Flux candidateVerified, actually orderable functionally similar alternative. Frequency, CL, tolerance, temperature class, AEC-Q200 family, and body class align; higher worst-case ESR may reduce startup margin. Footprint interchangeability was not dimension-by-dimension verified, so it is not claimed as a drop-in.
Seiko Epson FC-135 32.7680KA-AG5Flux identifies this exact active MPN as a two-terminal 3.2 mm × 1.5 mm SMD crystal and indexes Mouser/Digi-Key availability. The FC-135 manufacturer family data specifies 32.768 kHz, 70 kΩ typical ESR, and 7/9/12.5 pF load options; the exact AG5 option decode was still awaiting machine-readable datasheet evidence during this pass.Available Flux candidateOrderable exact MPN, functionally similar only. Its exact CL/tolerance/temperature suffix details remain unverified here, and it must not be substituted without checking the Epson order-code specification and oscillator load design.
The Abracon exact MPN is the only alternative in this bounded pass with primary-datasheet verification of the complete load, tolerance, temperature, package, and packaging-option combination. The Epson row is an exact, distributor-indexed MPN but remains a functionally similar sourcing option pending suffix verification; neither alternative is claimed as footprint-verified or drop-in.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Manufacturer ordering suffix-TR denotes tape-and-reel packaging; the ECX-34Q datasheet specifies 3,000 pieces/reel.
JLCPCB / LCSC assembly listingJLCPCB part C2450046, Extended Part. Checked 2026-10-07: stock 0, minimum 6, full reel 3,000. These are live purchasing values and can change; reconfirm before release: https://jlcpcb.com/partdetail/ECS-ECS_327_6_34QCSTR/C2450046
Flux-indexed distributor leadsThe current Flux library record reports Mouser, Verical, and LCSC listings, but its indexed manufacturer MPN is ECX-.327-CDX-2096, not the project title MPN. Treat this discrepancy as a sourcing warning and verify the manufacturer label, 6 pF option, ±10 ppm option, and S temperature code before ordering.
Primary distributorsPrefer ECS-authorized channels or established franchised distributors such as Mouser and Digi-Key; verify current stock, MOQ, cut-tape availability, country of origin, and date/lot data on the distributor page at purchase time. Live MOQ/reel details beyond the JLCPCB listing were not independently verified.
Packaging optionsManufacturer-verified option is tape and reel, 3,000/reel. Distributor cut tape or custom reel may be offered, but those services are distributor-specific and unverified here.
Suffix controlOrder the complete ECS-.327-6-34QCS-TR string. 6 identifies 6 pF, 34Q identifies ECX-34Q, C identifies ±10 ppm, S identifies -40°C to +125°C, and TR identifies 3K/reel.
Counterfeit / substitution preventionDo not accept a shortened “32.768 kHz 3215 crystal” description. Require the full MPN on quote, packing label, and certificate; check ECS traceability, reel label, date/lot code, and authorized-channel status. Electrically screen suspect lots for frequency/load point, ESR, and startup behavior.
Incoming verificationConfirm package dimensions, reel label suffix, and certificate/traceability. For automotive builds, request the applicable AEC-Q200/PPAP documentation from ECS or the authorized distributor rather than inferring qualification from a marketplace listing.
Sources
Unverified information disclosure: Current distributor inventory, pricing, lead time, MOQ, and cut-tape services are dynamic. Except for the explicitly checked JLCPCB listing and manufacturer-specified 3,000-piece reel, purchasing quantities and availability must be reconfirmed at order time; the Epson AG5 suffix details and all alternative footprint interchangeability remain unverified.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources