I’ll research JST’s specifications and verified alternatives, then write a cited application and usage guide in the project files, clearly flagging any unverified details.
JST’s current PH catalog specifies a wider temperature range than distributor listings for this exact ordering code; I’ll flag that discrepancy rather than assume interchangeability. I also verified two functional alternatives, but neither is confirmed as a drop-in replacement.
The JST B3B-PH-K-S(LF)(SN) is a three-position, single-row, vertical through-hole PCB header in the 2.00 mm-pitch PH wire-to-board connector family. Its common application is a detachable internal cable connection carrying low-voltage power and signals between a PCB and a peripheral or subassembly; JST identifies the PH family as a compact internal-wiring interface with friction-lock mating. JST product profile
1. Quick Specifications
Rating terminology: JST publishes connector ratings and qualification tests, not a semiconductor-style “Absolute Maximum Ratings” table. Rated current and voltage are operating ceilings under their state...
Created and checked the Application & Usage Guide in the project files, covering all seven requested sections with citations and source links.
The guide flags conflicting temperature ratings and unverified drop-in compatibility; before design release, confirm the supplied-lot rating and validate pin orientation and footprint geometry.
The JST B3B-PH-K-S(LF)(SN) is a three-position, single-row, vertical through-hole PCB header in the 2.00 mm-pitch PH wire-to-board connector family. Its common application is a detachable internal cable connection carrying low-voltage power and signals between a PCB and a peripheral or subassembly; JST identifies the PH family as a compact internal-wiring interface with friction-lock mating. JST product profile
1. Quick Specifications
Rating terminology: JST publishes connector ratings and qualification tests, not a semiconductor-style “Absolute Maximum Ratings” table. Rated current and voltage are operating ceilings under their stated conditions, not recommended design targets; a dielectric withstand test is not an operating-voltage rating.
Table
Parameter
Value
Classification and practical interpretation
Positions and orientation
3 circuits; top-entry through-hole header
Mechanical configuration for B3B-PH-K-S.
Pitch
2.00 mm
Nominal PCB hole spacing; drawing tolerance ±0.05 mm, without cumulative pitch error.
Rated current
2 A AC/DC with AWG #24 wire
Manufacturer rating under the stated wire condition; do not assume this rating applies unchanged to thinner wire, poor crimps, or every ambient temperature.
Rated voltage
100 V AC/DC
Connector rating, not a declaration that an assembled product meets mains-safety requirements.
Current PH catalog temperature range
−40°C to +105°C, including temperature rise from current
Current manufacturer series specification; applicability to all stock bearing this exact legacy ordering code is not resolved. See discrepancy below.
Initial contact resistance
10 mΩ maximum
Specification, not a typical value.
Contact resistance after testing
20 mΩ maximum
Post-test specification.
Insulation resistance
1,000 MΩ minimum
Insulation specification.
Dielectric withstand
800 VAC for one minute without breakdown or flashover
Qualification test only; never use 800 VAC as working voltage.
Header dimensions
A = 4.0 mm; B = 7.9 mm in JST’s header table
Use the associated drawing to interpret datums; A is the three-pin span.
Top-entry assembly envelope
8 mm mounting height; 4.5 mm width
Catalog assembly dimensions; allow additional clearance for wires and removal.
Post / base housing
Tin-plated copper alloy / natural-white PA
Current catalog material description; it does not establish a more specific alloy or PA grade for every supplied lot.
Recommended application voltage
For example, a 3.3 V or 5 V peripheral supply
Application examples, not a manufacturer-specified nominal voltage. Choose voltage to match the connected electronics.
Absolute maximum ratings / typical operating point
No separate absolute-maximum table or universal typical operating point established in the reviewed evidence
Do not invent either for a passive connector.
Temperature discrepancy: The current JST PH product profile and catalog specify −40°C to +105°C, whereas LCSC’s exact B3B-PH-K-S(LF)(SN) listing reports −25°C to +85°C. Until JST confirms the exact supplied revision/lot, keep an existing design within the narrower −25°C to +85°C envelope including self-heating; this conservative recommendation is not a declaration that the wider rating is invalid. Independent extraction of the older mirrored catalog’s temperature and 0.8–1.6 mm PCB-thickness specifications remained pending, so those legacy datasheet claims are not independently verified here.
2. Pinout & Connections
This is a passive connector: its contacts have no fixed GND, VCC, signal, or polarity assignment. The following table describes contact identity, not an imposed application pinout.
Table
Pin Number
Pin Name
Description
Best Practice
1
Contact 1
First numbered contact; user-defined net
Assign a descriptive net and mark pin 1 on silkscreen and the harness drawing. Do not assume pin 1 is positive supply.
2
Contact 2
Middle contact; user-defined net
If assigned to supply, verify voltage and current against both the connector and load requirements.
3
Contact 3
Remaining contact; user-defined net
If assigned to a signal, apply that interface’s biasing, protection, and logic-level rules—not generic connector pull-ups.
Orientation check: JST’s PCB layout is viewed from the connector mounting surface. The exact left-to-right pin-number orientation relative to the shroud/key was not independently established in this research; confirm it using JST’s exact drawing, the footprint pad numbers, and a physical sample before release. A cable viewed from its mating face can appear reversed relative to a board viewed from its solder side. Verify every intended contact-to-contact connection with a continuity test.
3. Standard Application Circuit
A common use is a three-wire peripheral harness carrying ground, supply, and one analog or digital signal. The assignment below is an illustrative system convention, not a JST-defined standard:
Choose V_PERIPH from the peripheral’s requirements; do not connect a 5 V signal directly to a non-5-V-tolerant MCU input. Define signal direction and voltage in the schematic and cable drawing.
The cable-side component is the three-circuit PHR-3 housing. Populate it with properly selected PH receptacle contacts; SPH-002T-P0.5S accepts AWG #30–#24 conductors (0.05–0.22 mm²) and 0.8–1.5 mm insulation outside diameter. Purchase the header, housing, and three contacts separately unless buying a qualified preassembled harness.
No resistor, capacitor, pull-up, or pull-down is required by the connector itself. Add peripheral decoupling to the load IC’s specification. A 100 nF ceramic close to a peripheral supply pin is a common starting point, not a JST requirement; bulk capacitance must be chosen for load steps, cable impedance, and upstream regulator stability.
A push-pull signal needs no pull-up merely because it passes through this header. An open-drain interface needs an appropriately calculated pull-up to its permitted logic rail; there is no universally correct 10 kΩ value.
If the harness is user-accessible or exposed to transients, evaluate ESD protection near the board entry and fault-current limiting in the supply path. Select these from the system’s actual exposure and current limits.
This is not a USB connector or an LED, so USB CC resistors, shield termination rules, and LED series-resistor calculations do not apply.
4. PCB Layout & Routing Guidelines
Use the top-entry through-hole drawing, not an SMT or side-entry PH footprint. JST gives Ø0.7 mm holes with +0.1/0 mm tolerance, 2 mm ±0.05 mm pitch, and no cumulative pitch error, viewed from the mounting surface. Hole dimensions are reference values dependent on PCB material and drilling method; JST specifically advises considering larger holes for hard fiberglass-cloth boards. Coordinate finished plated-hole size, plating allowance, annular ring, and lead-retention fit with the fabricator rather than blindly treating the reference hole size as a drill-tool diameter.
Reserve the mating and service envelope. The three-circuit header table gives B = 7.9 mm, and the catalog describes an 8 mm-high, 4.5 mm-wide top-entry assembly. Keep adjacent components clear of the housing, wire bend, and vertical unplugging path; do not interpret the assembly height as the bare-header height.
Size the entire current path. Select supply and return trace widths from copper thickness, route length, acceptable drop, and temperature rise; check vias, neck-downs, and thermal spokes as well. The 2 A rating is tied to AWG #24, not a blanket recommendation to run 2 A through any trace or cable. No universal “2 A trace width” is specified by JST.
Balance solderability and electrical performance. Thermal relief can ease soldering to planes, but undersized spokes can become bottlenecks. Verify solder fill and seating with the intended hand, wave, or selective-solder process; mechanical retention is not a substitute for a qualified solder joint. Do not assume suitability for a normal SMT reflow profile without exact-part process approval.
Route for the actual interface. Place decoupling at the load IC, not automatically beside the header. For low-speed signals, provide a short return path; no differential-pair impedance or high-speed channel performance was verified for this part, so matching PCB traces alone does not qualify the connector and cable for USB or other high-speed interfaces.
5. Common Pitfalls / Things to Watch Out For
Treating “JST 2 mm” or a keyed housing as proof of electrical compatibility. PH, other JST families, and other manufacturers’ 2 mm systems are not automatically interchangeable. A polarized connector also does not enforce VCC/GND assignment: document the harness pin map, verify the viewing direction, and continuity-test the assembled cable. JST describes PH as friction-lock mating, not as a universally interchangeable positive-latch system. JST profile
Assuming full rated current, broad temperature capability, or solderless press-fit assembly from a distributor field. The 2 A rating has an AWG #24 condition, and the temperature limit includes current-induced rise. Poor crimps and narrow copper increase heating; the conflicting temperature listings require exact-lot confirmation. Distributor “press-fit” terminology is not evidence of a qualified compliant-pin, solderless interface—use a qualified through-hole solder process unless JST explicitly approves otherwise.
6. Popular Alternatives & Equivalents
No cross-manufacturer drop-in replacement was verified. The following are verified functionally similar connector systems. A shared three-contact, 2 mm pin grid does not establish footprint compatibility, identical pin numbering, or compatibility with a JST PHR-3 cable housing.
Functionally similar only; pin/footprint compatibility with JST not verified
Use the specified Molex 51065-series mating housing and applicable terminals; the drawing lists 51065 and 502128*00. Revalidate footprint, retention, cable, and enclosure clearance.
3 positions, 2 mm contact and mounting pitch, straight THT; manufacturer lists an 8 × 5 × 5 mm connector. Hirose exact-part page
Functionally similar only; pin/footprint compatibility with JST not verified
Select the appropriate DF3 mating cable components and review the exact drawing. Flux library metadata currently labels this result Surface Mount/CONN-SMD, contrary to Hirose’s THT description; inspect and validate the footprint before use. This metadata discrepancy alone does not establish whether the actual footprint is defective.
Availability in Flux is not mechanical qualification. Neither alternative is claimed to mate with a JST PHR-3 housing, and neither is a procurement-only substitution without engineering review.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Exact-code purchasing references verified here include TME, LCSC C131339, and TLC Electronics. Prefer a JST-authorized/franchised channel and verify authorization for your purchasing region; this guide does not independently certify every listed seller’s franchise status.
Packaging Options
Loose/bulk through-hole headers; TME describes a manufacturer bag of 1,000. JST’s B3B-PH-K-S table specifies 1,000 top-entry headers per box. Bag/box terminology can reflect distributor repacking. Do not assume tape-and-reel or cut-tape for this exact through-hole code.
Standard MOQ
No universal distributor MOQ: TME lists 1 piece; LCSC lists minimum 10 and multiples of 10. The 1,000-unit factory pack is not necessarily the retail MOQ. These are listing observations checked October 7, 2026, not guaranteed future terms.
Sourcing Advice
Order the full B3B-PH-K-S(LF)(SN) code and confirm three positions, vertical through-hole orientation, specified finish, packaging, and exact temperature qualification. JST notes that the product displays (LF)(SN) on a label. The reviewed evidence does not support treating these suffixes as tape/reel designators. Check the lot label and certificate rather than relying on a stock photograph. Avoid untraceable marketplace stock or generic “JST-compatible” listings when mating fit and crimp quality matter.
For JLCPCB assembly, C131339 is listed as an extended through-hole part with wave-soldering assembly. Confirm current stock, fees, and assembly eligibility with the quote; inventory quantities and prices are intentionally not represented as durable specifications.
Sources
Manufacturer documents establish electrical and mechanical specifications; distributor pages are used for ordering-code observations, MOQ, and packaging. Application examples and PCB recommendations are engineering guidance, not claims of a manufacturer-prescribed application circuit.
JST, PH CONNECTOR current English catalog:ePH.pdf, Specifications; PC board layout and Assembly layout; Contact; Housing; Header; Model number allocation. Reviewed October 7, 2026. An explicit document revision/date was not established in the extracted evidence.
JST, PH connector product profile:Series 199. Primary source for series description, friction lock, and current temperature range; accessed October 7, 2026.
Molex, 532530370 exact-part page:Product page, accessed October 7, 2026; online catalog currently provides limited exact-part information.
Molex, MICRO-LATCH 2.0 WTB VERTICAL HEADER ASSY customer drawing:2406281007_MOLEX-532530370_C240846.pdf. Source for mounting, circuit count, pitch, and mating-family notes; exact drawing revision/date not independently established.
Hirose, DF3-3P-2DSA(01), CL0543-0018-5-01:Manufacturer product page and document links. Product specifications display “Last Updated On February 07, 2026”; that is a web-specification update date, not necessarily a drawing revision.
Unresolved verification: Exact pin-number orientation relative to the housing key; supplied-lot applicability of the expanded temperature range; exact qualified PCB-thickness range and soldering profile; older catalog extraction; and cross-manufacturer drop-in compatibility. None is inferred from matching pitch alone.