DIY Thermal Station Design


I applied the 160 × 100 mm, four-layer setup and component placement; the placement checks now show no errors or warnings. Autorouting is blocked, with 40 connections remaining: USB-C mounting compatibility and ESP32 antenna clearance need resolution, and I also found ultrasonic power/echo-divider problems—details are in Placement Handoff. I recommend correcting these before routing; may I replace the incompatible USB-C connector and repair the affected circuitry?
yes
I’ll replace the incompatible USB-C connector, correct the ultrasonic supply and echo levels, and resolve the thermal-sensor and antenna constraints before routing. I’ll also check the power budget so the repairs don’t rely on an undersized or unreliable battery supply.
Finished execution
"Thermal Station Repairs" completed.
I corrected U6’s enable connection, moving CE from its own 3.3 V output to VBAT to remove a startup dependency. That change was applied, but post-change ERC and simulation were not completed.
The repair work remains unfinished:
  • Replace USB-C after verifying the replacement’s mechanical compatibility.
  • Add battery-powered ultrasonic supply and correct the echo divider.
  • Verify and repair AMG8833 support circuitry.
  • Complete the power budget, antenna clearance, and documentation updates.
  • Finish placement changes, autorouting, and final DRC.
No PCB placement or routing changed this session; the previously applied layout remains a draft, not manufacturing-ready. Execution stopped because your ACUs ran out.

Waiting for input


Placement Handoff
Assigned-scope status
  • Completed: manufacturing target, explicit 160 × 100 mm rectangular board setup, all 21 top-level physical parts placed on Top, nine missing functional groups assigned and verified, placement checks, intact charger internal routing retained.
  • Failed / blocked: final ESP32 antenna copper-clearance signoff. The actual DevKit antenna-to-header geometry was not established by available immutable evidence. No guessed protected polygon was added. Ground fill/stitching exists near the MCU, so resolve an all-layer antenna exclusion before autorouting or fabrication.
  • Failed / blocked: USB-C exact edge mating signoff. J1 is positioned at the bottom-left edge provisionally, but the MPN's manufacturer product page identifies a mid-mount connector; web-indexed drawing indicates a PCB cutout and 0.80 mm board thickness. The current carrier is rectangular and about 1.56 mm stackup thickness. PDF evidence for exact cutout/thickness remained pending, not absent. Resolve MPN-versus-footprint compatibility or choose a compatible connector; no cutout or board thickness change was guessed.
  • Unattempted intentionally: autorouting, schematic redesign, new mounting holes, enclosure fitting. Enclosure envelope is provisional; IP65 alone specifies no dimensions.
Applied manufacturing target
Project-fit recommended Standard Density (SDI), version 3, Flux official UID mfp_23e942b5-5c91-4fd8-ad4d-d1d2d3e51999; effective state remained applied. Its companion JLCPCB SDI 4 Layer, version 1, UID mfp_promoted_2dd12d2c-0d2e-4294-a994-fa16faefbffc, was automatically applied and is also applied.
The companion replaced the former standard four-layer physical stackup: four 0.035 mm copper layers, FR4/Core, approximately 1.56 mm displayed overall thickness; Top signal / Mid-Layer 1 Power Plane / Mid-Layer 2 signal / Bottom signal. Through-hole via template is 0.55 mm pad / 0.25 mm drill. No HDI was introduced. Board outline was then explicitly set to 160 × 100 mm before placement without replacing the companion stackup. Profile application removed previous untagged/named rulesets by tool behavior and retained node overrides.
Placement (source origins, mm; not bounding-box centers)
All top side. Board center is (0,0), edges ±80 X, ±50 Y. No locks or mounting holes were deliberately removed or added.

Table


PartXYRotation
ESP32 U1-55460°
AMG8833 U2-4420°
Ultrasonic US14229180°
SD U4676270°
RTC U71670°
Charger U5-58-170°
LDO U6-35-140°
Battery BT1-15-340°
USB-C J1-70-46.50°
R1 / R2-2332 / 290°
R6 / R7-6136 / 330°
R4 / R538 / 43230°
R35240°
R8 / R9-70.5 / -66.5-370°
C4 / C5-39 / -31-140°
C6-59460°
Sensor region is at top, battery bottom separated from sensing, charger/USB bottom-left. The thermal package senses normal to the PCB; enclosure sensor apertures and ultrasonic mounting remain provisional. SD header faces inward/left, card insertion edge outward/right. The module's documented card insertion direction is from the edge opposite its header row toward the header.
Nine groups: MCU U1 Controller; SENSE U2 Thermal Array; SENSE US1 Ultrasonic; DIGITAL U4 SD Storage; DIGITAL U7 RTC; IO J1 USB-C Power; POWER U5 Battery Charger; POWER BT1 Battery; POWER U6 3V3 LDO.
Nested-module API anomaly and repair
mutate_layout_component_positions rejected full UIDs. Its ref: U5 incorrectly changed the last nested element STDB instead of the U5 parent. STDB native source position became (-58,-17) locally. Its baked original local geometry was restored with UID-targeted ruleset Restore charger STDB local position, UID d4fdc9eb-70aa-4290-bdc8-4664b92d6960, position = 8.326mm -0.844mm !important. Direct child rule repair was rejected because the child belongs to U5.
U5 parent was moved safely by exact node UID using node rules. Image readback verifies the charger cluster and copper together at bottom-left, not scattered; remaining children retain their original local coordinates. Keep the STDB repair override until its source position can be repaired through a hierarchy-aware API. Do not use generic placement/packing on U5 or its duplicate U1/R1/R2 labels.
Verification evidence
  • Final placement-tool feedback: 0 body overlaps, 0 keepout violations, 0 outside-board parts.
  • Read-only layout image inspected: all top-level parts on board; SD accessible right edge; charger internal traces move with cluster; battery clear of sensors.
  • Final requested DRC batch: component outside board, body overlap, keepout, edge placement, neckdown escape, pad access, stackup, protected intrusions, invalid pads: 0 errors / 0 warnings. One Info remains for U4's footprint under Invalid Pads; no detailed diagnosis supplied. Info is not evidence of a definite wrong pad.
  • A C6 decoupling-loop warning was observed and C6 was moved closer to the DevKit 3V3 pin. Final Placement Checks query returned no remaining findings.
  • Routing-state readback: 40 airwires; zero redundant traces in zero groups. Existing 33 route segments are module internal copper; none deleted and no autorouter called.
  • Profile/stackup application activates a ground fill and stitching (layout summary increased visible vias from 3 to 61); this explains fewer airwires without routing. Antenna clearance is not yet certified.
Routing handoff
Geometry is a usable placement draft, not fully route-ready until antenna exclusion and J1 fit are resolved; electrical blockers below also precede release.
Profile minimum trace/clearance: 0.127 mm; default signal width: 0.15 mm; ordinary copper keepout: 0.15 mm. Through-hole pad trace minimum clearance 0.30 mm is part of the profile. Before routing, set current-based overrides on USB_5V and VBAT (schematic Max Current 1 A), and 3V3 (0.6 A); 0.15 mm defaults are not a validated power-path width. Power widths were not changed in this placement-only batch. A provisional starting point for the lead is 1.0 mm main USB_5V/VBAT and 0.6 mm 3V3 on 1 oz outer copper, with justified short neckdowns at fine pads; verify drop/thermal/current budget before using as requirements. Keep signal/GND escape defaults narrow and rely on a continuous ground plane, not blanket-wide GND traces. Preserve U5 internal 0.254/0.508 mm traces. No USB data pair exists on this power-only connector.
Visible electrical blockers (no schematic edits)
Read existing Hardware Safety Alternatives and verified current net memberships.
  • Error / functional blocker: 5V_SENSOR only connects U1 5V and US1 VCC; no battery-powered 5 V generator exists. USB_5V only connects J1 and charger VIN, not this rail. Battery operation cannot be assumed to power HC-SR04. Avoid powering the DevKit simultaneously through independent 3V3 and USB/5V paths without checking its official constraints.
  • Warning / unverified pin usage: U2 AVDD-PC and DVDD-PC are tied directly to 3V3. Available Panasonic document did not resolve those pin functions. Do not treat the safety note's library-model workaround as datasheet approval. The supplied internal-circuit drawing specifies 10 µF between VDD pin 9 and GND pin 6. There is no dedicated local U2 capacitor in the current physical inventory; lead should resolve exact bare sensor support circuit.
  • Error / documentation mismatch: BATTERY_SENSE is on U1 VP, not GPIO35/IO35 as R6/R7 Role Details claim. Firmware mapping needs reconciliation; no net changed.
  • Warning: echo divider uses 20 kΩ high side and 10 kΩ low side; nominal 5 V input yields 1.67 V, not a 3.3 V logic high. Verify ESP32 VIH margin before relying on it.
  • Warning: TP4056 load sharing, battery protection and temperature monitoring remain unresolved; TEMP is grounded. Battery holder protected-cell length compatibility was not proven.
  • Warning: LDO peak current/dropout/thermal/runtime remain unbudgeted; SD-write/radio transients and cell discharge range require analysis.
No part replacement, net edit, passive-value change or protection redesign was performed. Completion of this batch's placement geometry is separate from final board electrical/mechanical acceptance.
  • Assigned-scope status

  • Applied manufacturing target

  • Placement (source origins, mm; not bounding-box centers)

  • Nested-module API anomaly and repair

  • Verification evidence

  • Routing handoff

  • Visible electrical blockers (no schematic edits)